SYNTECH FIX EP

Thixotropic epoxy adhesive in cartridge form for structural anchors

Code: RNF.0379

Composants: 1

Aspect: Pâte

SYNTECH FIX EP is a two-component structural adhesive based on epoxy resins for anchoring and structural fastening on concrete surfaces, stone materials, bricks, wood and building materials in general. Given the elevated adhesion and resistance capacity against stresses due to high loads and the rapid development of mechanical resistance, SYNTECH FIX EP is suitable for anchoring bars and gluing metal elements. SYNTECH FIX EP can also be used as a soldering agent between materials of varying nature.

Linee di appartenenza

Certifications obtenues et Normes

ETAG 001 Part 5 OPTION 1

ETAG 001 Part 5 OPTION 1

ETAG 001 Part 5 OPTION 1

ETAG 001 TR 023

ETAG 001 TR 023

ETAG 001 TR 023

ETAG 001 Annex E

ETAG 001 Annex E

ETAG 001 Annex E

Caractéristiques générales

conservabilité

Conservabilité: 24 mois

température-d-utilisation

Température d'utilisation: +5 / +35 °C

utiliser-en-portant-des-gants-de-protection

Utiliser en portant des gants de protection

utiliser-en-portant-des-lunettes-de-protection

Utiliser en portant des lunettes de protection

Spécificités techniques

Résistant aux agents chimiques

Couleurs disponibles

- Gris

Emballages et dimensions

- Cartouche Bi-Mix 470 ml

- Boîte: 12 x (Cartouche Bi-Mix 470 ml)

Consommations

Consult the technical staff.

Champs d'utilisation

SYNTECH FIX EP is used as an adhesive to create structural anchors of threaded bars with improved adhesion, metal elements, fastening between materials of a different nature (steel, concrete), applications on wet or humid media, grouting cracks, repairs and filling, sealing of large diameter holes or applications with high-diameter bars and high-power dielectric anchors by cancelling the effect of stray currents.

Préparation des supports

Remove all crumbly parts with low mechanical strength and that are starting to detach from the affected area, completing the anchor holes on a healthy and compact substrate. Create the hole, checking its perpendicularity and blowing out the hole with compressed air. The holes must be cleaned and dedusted – remove any dust, oil, grease, paint, dirt, debris and any other residue that could affect adhesion.

Modalités d'utilisation

The two components of SYNTECH FIX EP are packaged in a single 470 ml two-component cartridge with side-by-side sections. The components are blended in the mixing nozzle during extrusion, to be carried out with a special gun. SYNTECH FIX EP is ideal for fastenings with variable anchoring depth, to grant the drafter a high degree of flexibility. Screw the nozzle to the cartridge and insert into the pump. Protect the hands and face during preparation. Before proceeding with the application, ensure that the two components are completely mixed by extruding a small amount of product – if it emerges in a uniform colour, it has been properly mixed. Only at this point is the cartridge ready for use. Extrude SYNTECH FIX EP into the hole until it is filled to 2/3. Use a threaded bar cut at 45° on the end going into the hole. Insert the bar with a rotating motion to allow the air bubbles to escape. Respect the hardening and application times indicated on the data sheet.

Méthodes d'application

- Pistolet de dosage

Nettoyage des instruments

- Diluant Nitro

Supports autorisés

- Béton

- Bois

- Chapes de support

- acier

- Briques

- Pierres naturelles

Contactez-nous dès maintenant

Vuoi saperne di più sui nostri prodotti?

Attention, veuillez remplir correctement ce champ.
Attention, insérer une adresse email valide.
Attention, veuillez remplir correctement ce champ.

En soumettant, j'accepte les déclaration de confidentialité

Attention, veuillez remplir correctement ce champ.

Inscription à la newsletter

Partager

Produits en vitrine

  • Syntech H.A.G.
  • Concrete Repar
  • Pro Seal